Sticking my fingers where they do not belong.
Short version of a long story. I was holding my torch when I triggered it with the other hand.
Oddly enough no pain. I knew instantly because of the flash and let it go. Initially the hole was 1/8 inch deep, no blood, it was cauterized. Swelling had already lessened the depth when the photo was taken.
My coworkers brought in a car accident patient while I was in emerg and had a good laugh.
Not sure if I got the photo to show up.
David
[attachment=0]Toasted Finger.jpg[/attachment]
Where no finger should go.
-
- 2.5 Star Member
- Posts: 163
- Joined: Tue Apr 19, 2016 10:29 pm
- Location: In the way.
Where no finger should go.
You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here
Last edited by sawdust1 on Tue Jan 10, 2017 6:31 pm, edited 2 times in total.
-
- 2 Star Member
- Posts: 85
- Joined: Sun Dec 27, 2015 8:02 am
Re: Where no finger should go.
Don't see the pic but it sounds painful... If not today then in a few days it's going to hurt like a bitch.
-
- 3.5 Star Elite Contributing Member
- Posts: 593
- Joined: Thu May 12, 2011 4:28 pm
Re: Where no finger should go.
That is the benefit of being burned by plasma...instant cauterization. We had a customer that hand a hand cutter on a 150 amp plasma that blew out the back and put a nice hole in his hand. It just proves that we must be extremely cautious working around these powerful pieces of equipment.
-
- 3 Star Elite Contributing Member
- Posts: 255
- Joined: Wed Apr 29, 2009 8:14 am
- Location: Helotes, TX
Re: Where no finger should go.
Strange. My old Esab system had hi frequency start and the tech that worked on it would put the nozzle to his hand and pull the trigger to see if the hi freq would start. Not much happened, but that was how he checked for proper hi freq. I never tried it and don't regret it.
Victor Simonis
Grey Forest MetalCraft
Helotes, TX 78023
210-872-2622
Sector Technologies Photon 5x10 water table machine with Hypertherm Micro Edge Controller, Powermax 105
Grey Forest MetalCraft
Helotes, TX 78023
210-872-2622
Sector Technologies Photon 5x10 water table machine with Hypertherm Micro Edge Controller, Powermax 105
-
- 3.5 Star Member
- Posts: 681
- Joined: Wed Nov 26, 2014 5:12 pm
Re: Where no finger should go.
You must be left handed
-
- 2.5 Star Member
- Posts: 163
- Joined: Tue Apr 19, 2016 10:29 pm
- Location: In the way.
Re: Where no finger should go.
Today, I am a lefty!
-
- 3 Star Member
- Posts: 273
- Joined: Sat Oct 06, 2012 7:16 pm
Re: Where no finger should go.
What did they do for it at the ER?
-
- 2.5 Star Member
- Posts: 142
- Joined: Thu Jan 31, 2013 11:40 am
Re: Where no finger should go.
It looks to me like you got quite a bevel on that cut. You should check the O-ring on your torch.
-
- 2.5 Star Member
- Posts: 163
- Joined: Tue Apr 19, 2016 10:29 pm
- Location: In the way.
Re: Where no finger should go.
Cleaned it, gave me some Flamazine and told me to wash it in saline and put the cream on it twice a day for a week. Surprisingly I did very little damage to it! Looked way worse than it is. I was cutting at 25 amps.
- SeanP
- 4 Star Member
- Posts: 950
- Joined: Thu Aug 01, 2013 11:50 am
- Location: Co Kerry, Ireland
Re: Where no finger should go.
You have nailed the centre marking, that looks perfect!
Ouch
Ouch
Powermax XP45
Home built table, Candcnc DTHC 2, Dragoncut 620-4
R-Tech 210 Tig, Jasic 250 mig
Sheetcam, Scanything, Coreldraw
Table build gallery
Home built table, Candcnc DTHC 2, Dragoncut 620-4
R-Tech 210 Tig, Jasic 250 mig
Sheetcam, Scanything, Coreldraw
Table build gallery