Hey Everyone New member here,
Canadian in Ontario
I have a Hypertherm 130 on a vicon automated cnc table
currently I have consumables for aluminum mild steel and stainles between 45 -130
the table has a front and back or an all selection allowing me to cut single pieces up to 250'' x 75'
not the best at cad or drawing in the vicon program but i am slowly learning and hope to contribute and share as I get better.
introduction
- little blue choo
- 4 Star Member
- Posts: 1460
- Joined: Mon Mar 02, 2015 10:38 pm
- Location: Cherryville NC
- Contact:
Re: introduction
Welcome Drogers. Jump in and get your feet wet. Hopefully this forum will be a big help to you. It sure was for me.
Rick
Rick
Rick
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
- exapprentice
- 3 Star Member
- Posts: 357
- Joined: Mon Jul 06, 2015 1:57 pm
- Location: Wiltshire, UK
Re: introduction
Hi Drogers
now you have jumped in and got your feet wet, welcome aboard and dry out a little
now you have jumped in and got your feet wet, welcome aboard and dry out a little
Best Regards to all
Exapprentice
(Pete)
10'x5' DIY table / PM 45XP + M/C Torch - Trying to add 4 axis Tube cutting
Linux/CommandCandCNC MP3600 / PN200 / DCP-01 / PWM
Solid Edge, Inkscape, SheetCam, Scananything & Andonstar USB Microscope
Exapprentice
(Pete)
10'x5' DIY table / PM 45XP + M/C Torch - Trying to add 4 axis Tube cutting
Linux/CommandCandCNC MP3600 / PN200 / DCP-01 / PWM
Solid Edge, Inkscape, SheetCam, Scananything & Andonstar USB Microscope
- Gamelord
- 4.5 Star Member
- Posts: 1637
- Joined: Wed Aug 29, 2012 5:17 pm
- Contact:
Re: introduction
Welcome, if you need any help, don't hesitate to ask.
Once you take flight, your eyes will forever be turned to the sky." "Lack of appreciation is the worlds biggest crime."
Torchmate 6x14 w/THC Downdraft
Thermal Dynamics Cutmaster 101
Corel Draw / Adobe Illustrator
Torchmate CAD
Torchmate 6x14 w/THC Downdraft
Thermal Dynamics Cutmaster 101
Corel Draw / Adobe Illustrator
Torchmate CAD
-
- 3.5 Star Member
- Posts: 681
- Joined: Wed Nov 26, 2014 5:12 pm
Re: introduction
Welcome to the site
- drodgers
- 1 Star Member
- Posts: 24
- Joined: Fri Feb 17, 2017 8:01 am
Re: introduction
thanks Guys, im excited to have found a helpful and share based online group!
Vicon Table
hypertherm hpr 130
Haco cnc brake
hypertherm hpr 130
Haco cnc brake