Image
To close this announcement click the X in the top right corner.
Industry Pros use FastCut CNC

Cutmaster 60I to Proma THC

Thermal Dynamics plasma cutter discussion forum.
Post Reply
healinhand
1/2 Star Member
1/2 Star Member
Posts: 3
Joined: Sat Jun 20, 2020 1:08 pm

Cutmaster 60I to Proma THC

Post by healinhand » Sat Jun 11, 2022 11:13 am

Could someone help me with wiring these 2 together? I`m running an AXBB-e controller, also

adbuch
5.5 Star Elite Contributing Member
5.5 Star Elite Contributing Member
Posts: 4767
Joined: Thu Sep 21, 2017 5:22 pm
Location: Tucson, Arizona
Contact:

Re: Cutmaster 60I to Proma THC

Post by adbuch » Sat Jun 11, 2022 11:01 pm

More details and some photos showing wiring diagrams, etc. may be helpful here.
David

robertspark
4.5 Star Elite Contributing Member
4.5 Star Elite Contributing Member
Posts: 1588
Joined: Mon Jun 12, 2017 6:43 pm

Re: Cutmaster 60I to Proma THC

Post by robertspark » Sun Jun 12, 2022 5:12 pm

http://cncdrive.com/downloads/CompactTHC_manual.pdf

https://www.cncdrive.com/AXBB.html

How far have your got?
AXBB-E_5.png
If you need to buy a CPC you can buy the following items:
1x 206044-1 https://www.google.com/search?q=206044- ... e&ie=UTF-8
1x 206070-8 https://www.google.com/search?q=206070- ... e&ie=UTF-8
9x 66103-4 https://www.google.com/search?q=66103-4 ... e&ie=UTF-8

Wire the THC up to pins 5 and 6 of the CPC (Circular Plastic Connector)
2022-06-12 21_52_01-THC2-eng.png
From the PLASMA CUTTER (ignore the ARC OK on the Proma 150!), wire it up to an ISOLATED INPUT on the AXBBE
Same as that shown for either the PROBE or the ESTOP in the image below.
Zero Volt to the (-) of the isolated input of the AXBBE. {Say I3-)
24V wire to PIN 12 of the PLASMA Cutter
From PIN 14 of the PLASMA Cutter CPC wire back to (+) of the isolated input of the AXBBE. {Say I3+}

2022-06-12 21_58_53-THC2-eng.png

From The proma THC 150, wire 24V up to the COM.
Then from the UP and DOWN pins wire back to SEPERATE isolated inputs (+) on the AXBBE .... {Say I4+ and I5+}.
From the (-) isolated inputs wire then back to zero volts {Say I4- and I5-}

In order to fire the torch you will need to install a 24v relay and wire two of the contact connections of the relay (COM) and (NO) back to pins 3 and 4 of the PLASMA Cutter CPC.
2022-06-12 22_06_14-AXBB_E_manual.pdf.png
You will then need to wire the coil of the relay back to 24V on one side and then the other side of the coil back to an ISOLATED OUTPUT of the AXBBE. {say O1, same as shown in the image at the top of the page}

You will then need to set up the inputs (ArcOK, THCUP and THCDN) and output (to to fire the torch) in uccnc or Mach3 / Mach4.

You do not have access to view or download this file.
Become a Contributing Member to gain access to this feature. Click Here


adbuch
5.5 Star Elite Contributing Member
5.5 Star Elite Contributing Member
Posts: 4767
Joined: Thu Sep 21, 2017 5:22 pm
Location: Tucson, Arizona
Contact:

Re: Cutmaster 60I to Proma THC

Post by adbuch » Sun Jun 12, 2022 6:44 pm

:Like :Like :Like

healinhand
1/2 Star Member
1/2 Star Member
Posts: 3
Joined: Sat Jun 20, 2020 1:08 pm

Re: Cutmaster 60I to Proma THC

Post by healinhand » Sun Jun 12, 2022 9:22 pm

This is perfect!!!!!!
THANKS for the Help!!

Post Reply

Return to “Thermal Dynamics / Esab Plasma Cutters”

Industry Pros use FastCut CNC