http://www.nextengine.com/
I can't wait to see what capabilities this will add!
I have added a new toy to my bag-o-tricks
- Joe Jones
- 5 Star Elite Contributing Member
- Posts: 3086
- Joined: Sat Oct 11, 2014 2:33 pm
- Location: Franklin, KY., USA
- Contact:
I have added a new toy to my bag-o-tricks
Franklin, KY., USA
Samson 510 & 4x4
6” Z Rail Lift Kit for PlasmaCam
CreatBot D600 PRO 3D Printer
12 Lasers
FREE DesignEdge Training!
It is more fun when it isn't necessary!
Samson 510 & 4x4
6” Z Rail Lift Kit for PlasmaCam
CreatBot D600 PRO 3D Printer
12 Lasers
FREE DesignEdge Training!
It is more fun when it isn't necessary!
- little blue choo
- 4 Star Member
- Posts: 1460
- Joined: Mon Mar 02, 2015 10:38 pm
- Location: Cherryville NC
- Contact:
Re: I have added a new toy to my bag-o-tricks
Congratulations Joe. I looked it over and it looks very interesting. How do you plan on using it.
Rick
Rick
Rick
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
- Joe Jones
- 5 Star Elite Contributing Member
- Posts: 3086
- Joined: Sat Oct 11, 2014 2:33 pm
- Location: Franklin, KY., USA
- Contact:
Re: I have added a new toy to my bag-o-tricks
After I get to know the software, I am going to use it to make 3D carvings for outdoor signs, Halloween props, large reproductions of figurines, and a lot more.
Imagine scanning the sides of a gun that is equipped with a laser, a scope, a bi-pod, and a couple of other add-ons. Now you create the file that will carve out a glove fit foam insert for a gun case and line it with cloth, or leather, or velvet, or ??? What would a case like that be worth? I have one gun that is worth $12,000.00 and it does not currently have a case.
Imagine scanning and reproducing tombstones found in old graveyards, making replacement wood carved parts for old German coo-coo clocks, scanning and reproducing lamp parts for a lamp set where one was dropped and broken. The uses are wide and varied.
Imagine scanning the sides of a gun that is equipped with a laser, a scope, a bi-pod, and a couple of other add-ons. Now you create the file that will carve out a glove fit foam insert for a gun case and line it with cloth, or leather, or velvet, or ??? What would a case like that be worth? I have one gun that is worth $12,000.00 and it does not currently have a case.
Imagine scanning and reproducing tombstones found in old graveyards, making replacement wood carved parts for old German coo-coo clocks, scanning and reproducing lamp parts for a lamp set where one was dropped and broken. The uses are wide and varied.
Franklin, KY., USA
Samson 510 & 4x4
6” Z Rail Lift Kit for PlasmaCam
CreatBot D600 PRO 3D Printer
12 Lasers
FREE DesignEdge Training!
It is more fun when it isn't necessary!
Samson 510 & 4x4
6” Z Rail Lift Kit for PlasmaCam
CreatBot D600 PRO 3D Printer
12 Lasers
FREE DesignEdge Training!
It is more fun when it isn't necessary!