I just set up my new PM 65 on a machine table that has a Blade Runner from CandCNC. The Hypertherm is replacing a Brand X which I had used for several years. I am sure that I will have numerous questions as I get going, but to start with, I noticed what appears to be a loose section in the new machine torch. Is this normal? If not, how do I address it, or do I have the torch mounted incorrectly? Is it okay to send a Dropbox link with a short video? If not, how can I send the vid?
Thank you very much.
Steve
New Powermax 65
-
- 2 Star Member
- Posts: 71
- Joined: Fri Aug 11, 2017 7:28 am
New Powermax 65
4' x 4' DIY Table
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
- acourtjester
- 6 Star Elite Contributing Member
- Posts: 7792
- Joined: Sat Jun 02, 2012 6:04 pm
- Location: Pensacola, Fla
Re: New Powermax 65
the torch sections are screwed together like pipes have you tried to tighten it, also there are 3 screws that hold the tip portion on the torch they could be loose.
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
-
- 2 Star Member
- Posts: 71
- Joined: Fri Aug 11, 2017 7:28 am
Re: New Powermax 65
Prior to posting, I did do a search and found this (or similar) posting with photo. I then went after those screws and they seemed tight and I didn't want to over tighten them. I will remove the torch and check again.acourtjester wrote: ↑Sat Dec 29, 2018 2:29 pm the torch sections are screwed together like pipes have you tried to tighten it, also there are 3 screws that hold the tip portion on the torch they could be loose.
DSCN1659.JPG
Thank you..
4' x 4' DIY Table
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
-
- 2 Star Member
- Posts: 71
- Joined: Fri Aug 11, 2017 7:28 am
Re: New Powermax 65
I just checked again and those screws are tight. Maybe this will help. https://www.dropbox.com/s/xhd9dqexz6775 ... 2.MOV?dl=0Mr. Fixit wrote: ↑Sat Dec 29, 2018 3:13 pmPrior to posting, I did do a search and found this (or similar) posting with photo. I then went after those screws and they seemed tight and I didn't want to over tighten them. I will remove the torch and check again.acourtjester wrote: ↑Sat Dec 29, 2018 2:29 pm the torch sections are screwed together like pipes have you tried to tighten it, also there are 3 screws that hold the tip portion on the torch they could be loose.
DSCN1659.JPG
Thank you..
Thanks again..
4' x 4' DIY Table
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
- acourtjester
- 6 Star Elite Contributing Member
- Posts: 7792
- Joined: Sat Jun 02, 2012 6:04 pm
- Location: Pensacola, Fla
Re: New Powermax 65
Looking at your video I don't think that is right, I would call Hypertherm tech support.
Also Jim Colt replies to post here, I'm sure he will have a comment about that.
Also Jim Colt replies to post here, I'm sure he will have a comment about that.
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
-
- 2 Star Member
- Posts: 71
- Joined: Fri Aug 11, 2017 7:28 am
Re: New Powermax 65
I appreciate your time and comment.
4' x 4' DIY Table
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
-
- 5 Star Elite Contributing Member
- Posts: 3087
- Joined: Mon Jul 20, 2009 11:18 pm
- Location: North Carolina
Re: New Powermax 65
The area that looks loose should have internal threads....it looks like it simply needs to be tightened. It is a large diameter thread machined into both pieces of melamine / fiberglass tube. Jim Colt
-
- 2 Star Member
- Posts: 71
- Joined: Fri Aug 11, 2017 7:28 am
Re: New Powermax 65
Jim,
Thank you for your response. I was concerned that I was going to damage something since I feel resistance when trying to turn that part. I checked in with technical support and the gentleman that I spoke with suggested that I loosen the strain relief at the top of the torch And then tighten as you have suggested.
Steve
Thank you for your response. I was concerned that I was going to damage something since I feel resistance when trying to turn that part. I checked in with technical support and the gentleman that I spoke with suggested that I loosen the strain relief at the top of the torch And then tighten as you have suggested.
Steve
4' x 4' DIY Table
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
-
- 2 Star Member
- Posts: 71
- Joined: Fri Aug 11, 2017 7:28 am
Re: New Powermax 65
This was all that it took. Resolved. Thank you
4' x 4' DIY Table
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder
CandCNC Bladerunner
Hypertherm PM65 Machine Torch
Miller Vintage 250 Mig
Miller Syncro 180 Tig
Bridgeport 2J Mill - Fagor Dro
Southbend 14" x 40" EVS Lathe - Fagor Dro
Brook 18" Metal Shaper
Harig 612 Surface Grinder