Hello guys, i've been having problems with cutting thick steel on my plasma cutter so I consider buying Proma THC. But, I searched on youtube and in the videos i see that they are wiring it to slots I don't have in my driver. Would you be kind enough to tell me if I can connect it to my driver or replace it before I buy THC?
Thanks a lot
Can I Connect a Proma THC to my Z axis driver?
-
- 1 Star Member
- Posts: 24
- Joined: Sat Mar 20, 2021 8:09 am
- djreiswig
- 4.5 Star Elite Contributing Member
- Posts: 1939
- Joined: Thu Nov 19, 2015 10:02 pm
- Location: SE Nebraska
Re: Can I Connect a Proma THC to my Z axis driver?
Usually a THC is more helpful on thin material that can warp or flex while cutting. Thick material usually doesn't have these problems. What sort of issues are you having?
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
- acourtjester
- 6 Star Elite Contributing Member
- Posts: 7796
- Joined: Sat Jun 02, 2012 6:04 pm
- Location: Pensacola, Fla
Re: Can I Connect a Proma THC to my Z axis driver?
there are 2 types of Proma the 150 hooks to input on the BOB that same way the limits switches do. But you will need to have spare inputs to to hook the signals from the Proma 150 to the BOB. the other type is a SD and this is a stand alone type that hooks between the BOB and the Z driver. It is to switch signals to the Proma SD when the THC is needed so no input to the BOB. This unit has be very problematic and I would not use it.
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
-
- 1 Star Member
- Posts: 24
- Joined: Sat Mar 20, 2021 8:09 am
Re: Can I Connect a Proma THC to my Z axis driver?
Im burning through my spare parts rather quickly because my table is diy that is not everywhere perpendicular. I thought if i cut 1 inch steel with THC it might be better.
- djreiswig
- 4.5 Star Elite Contributing Member
- Posts: 1939
- Joined: Thu Nov 19, 2015 10:02 pm
- Location: SE Nebraska
Re: Can I Connect a Proma THC to my Z axis driver?
If your torch isn't perpendicular to your material, a THC will not help. You are going to have angular edges on all of your parts. This is going to be more noticeable on thicker material.
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
-
- 1 Star Member
- Posts: 24
- Joined: Sat Mar 20, 2021 8:09 am
Re: Can I Connect a Proma THC to my Z axis driver?
Ok I figured the rest out, i just need one more thing. My plasma does not have a voltage divider and on the Proma 150 it says it has a built-in one. Do I still need a voltage divider to connect the plasma to the THC?
-
- 2.5 Star Member
- Posts: 166
- Joined: Mon Sep 12, 2022 9:29 am
Re: Can I Connect a Proma THC to my Z axis driver?
You can hook it up directly with suitable HV wire as per manual.
Keep that wiring as short as possible.
Keep that wiring as short as possible.