Page 2 of 2

Re: EASYSCRIBER QUESTIONS

Posted: Tue Jun 26, 2018 9:27 am
by weldguy
mayper wrote:Hi Everybody,
I have a machine torch on my powermax 45, my question is how do I tell if its a Duramax torch.
Peter
Hey Peter, I am not sure how to tell, it may still be considered a Duramax torch I don't know. I was told that if your torch uses the consumable parts listed below this will work with your torch.
DuramaxConsumables.PNG

Re: EASYSCRIBER QUESTIONS

Posted: Tue Jul 03, 2018 4:19 am
by RobertJohnson
Will the easyscriber work with a Powermax 900, Pac hand torch? I know, old school, but it works, plus I got a good deal on it.
Thanks for any information you can provide.
Robert Johnson

Re: EASYSCRIBER QUESTIONS

Posted: Tue Jul 03, 2018 10:08 am
by weldguy
RobertJohnson wrote:Will the easyscriber work with a Powermax 900, Pac hand torch? I know, old school, but it works, plus I got a good deal on it.
Thanks for any information you can provide.
Robert Johnson
From what I know it is only available for newer Hypertherm models.

Re: EASYSCRIBER QUESTIONS

Posted: Thu Jul 05, 2018 10:42 am
by zoeconner
I have a HP with a T80 torch. Will it work?

Re: EASYSCRIBER QUESTIONS

Posted: Wed Jul 11, 2018 4:40 am
by RobertJohnson
Thanks, just wondered, was hoping it would work with the pac 123, hand torch. Think that's what I have

Re: EASYSCRIBER QUESTIONS

Posted: Wed Jul 25, 2018 5:13 pm
by Sampson Jones
Anybody want to tell me how to set this up in sheetcam ?

Re: EASYSCRIBER

Posted: Wed Jul 25, 2018 11:45 pm
by weldguy
motoguy wrote:When I want to draw with my ink pen, etc I just use the "Mach3" post, which is a router post.
I am not a Sheetcam user but above is what motoguy suggested near the beginning of this thread.

Re: EASYSCRIBER QUESTIONS

Posted: Thu Jul 26, 2018 5:47 pm
by Sampson Jones
Here my torch Hypertherm t45m iec60974-7 Im assuming the easy scribe will not work with this powermax torch ? Is that correct ?

Re: EASYSCRIBER QUESTIONS

Posted: Thu Jul 26, 2018 9:25 pm
by plasmanewbie
Sampson Jones wrote:Here my torch Hypertherm t45m iec60974-7 Im assuming the easy scribe will not work with this powermax torch ? Is that correct ?
No it won't, I looked into this myself before before buying mine. Look at weldguy's post at the top of this page and your torch must use those consumables for this to fit. Those consumables are found on the 65, 85, 105, and 45xp.

Re: EASYSCRIBER QUESTIONS

Posted: Fri Jul 27, 2018 8:36 am
by Sampson Jones
Thanks

Re: EASYSCRIBER QUESTIONS

Posted: Thu Sep 27, 2018 7:09 pm
by zoeconner
With a little mod it works with T80 hand tourch

Re: EASYSCRIBER QUESTIONS

Posted: Sun Nov 25, 2018 2:39 pm
by pmsplasma
I have a powermax 85. I just received my easyscriber and question is do I turn on my pm? and they said I do not have to mess with my settings . I use shopsaber and pronest . Can someone help me ?

Re: EASYSCRIBER QUESTIONS

Posted: Sun Nov 25, 2018 3:43 pm
by djreiswig
I don't have one, but I wouldn't think you would want your plasma cutter on since the scriber replaces the consumables. This might cause problems with the arc ok setting not showing up and not allowing the table to move.