Any one have a barrel racer, very little detail
-
- 3 Star Member
- Posts: 251
- Joined: Mon Jun 20, 2011 9:12 am
- Location: Cache, Oklahoma
Any one have a barrel racer, very little detail
I did the search and the two I found probably would not cut at 14 inches, need a silhouette, very little detail.
PlasmaRoute CNC 4 x 4
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
-
- 4 Star Member
- Posts: 1472
- Joined: Wed Feb 04, 2009 5:35 pm
Re: Any one have a barrel racer, very little detail
You could always use the ones here and delete some of the detail, I do that quite often with smaller pieces,especially on cars, much easier to take detail out than add it.
Murray
Murray
- Larry83301
- 5 Star Elite Contributing Member
- Posts: 2648
- Joined: Tue Oct 27, 2009 6:36 pm
- Location: Twin Falls, Idaho
Re: Any one have a barrel racer, very little detail
SignTorch has several that would cut small. Check out his site.
Larry
Larry
You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here
-
- 3 Star Member
- Posts: 251
- Joined: Mon Jun 20, 2011 9:12 am
- Location: Cache, Oklahoma
Re: Any one have a barrel racer, very little detail
When I download the files with too much detail into corel, I can only delete one node at a time, very time consuming,
but that is what I am doing now, anyone have any ideas on how to make it easier to delete a section?
but that is what I am doing now, anyone have any ideas on how to make it easier to delete a section?
PlasmaRoute CNC 4 x 4
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
-
- 4 Star Member
- Posts: 1472
- Joined: Wed Feb 04, 2009 5:35 pm
Re: Any one have a barrel racer, very little detail
To remove each object within a drawing, click on the object to select it, select shape tool and hold left mouse and drag around to select all nodes and hit delete, gone.
If you only want to remove some of the nodes and make adjustments to the drawing just drag around the nodes you want to remove and hit delete.
Murray
If you only want to remove some of the nodes and make adjustments to the drawing just drag around the nodes you want to remove and hit delete.
Murray
-
- 4 Star Member
- Posts: 883
- Joined: Fri Dec 03, 2010 7:57 pm
- Location: SE TX
Re: Any one have a barrel racer, very little detail
if you start with a dxf composed of (relatively smooth) short line segments, you can select all (or some) nodes, right click, and hit curve, then right click and hit smooth, and then try the reduce-nodes slider, of course you would want to deselect any hard corner nodes (before smoothing), and any sharp nodes that get distorted by smoothing can usually just be deleted (before node reduction)M & N Steel CNC wrote:When I download the files with too much detail into corel, I can only delete one node at a time, very time consuming,
but that is what I am doing now, anyone have any ideas on how to make it easier to delete a section?
I usually find myself using low values like 3 in the reduce nodes slider, because higher values usually cause unacceptable distortion, but it depends on the shape, sometimes it works better to lightly smooth the whole shape then re-smooth any sections that might need more smoothing
-
- 3 Star Member
- Posts: 251
- Joined: Mon Jun 20, 2011 9:12 am
- Location: Cache, Oklahoma
Re: Any one have a barrel racer, very little detail
Thanks for your help!
PlasmaRoute CNC 4 x 4
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
-
- 4 Star Member
- Posts: 900
- Joined: Thu Sep 03, 2009 10:43 am
Re: Any one have a barrel racer, very little detail
Try this one out.
You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here
-
- 3 Star Member
- Posts: 251
- Joined: Mon Jun 20, 2011 9:12 am
- Location: Cache, Oklahoma
Re: Any one have a barrel racer, very little detail
Thanks, MetalArt, I believe that will work.
PlasmaRoute CNC 4 x 4
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
-
- 3 Star Member
- Posts: 251
- Joined: Mon Jun 20, 2011 9:12 am
- Location: Cache, Oklahoma
Re: Any one have a barrel racer, very little detail
Took all the great files and made this one.
You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here
PlasmaRoute CNC 4 x 4
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake
Corel Draw X5
SheetCam
Baileigh 12 gauge 40 inch box brake