Snoopy & The Great Pumpkin
-
- 2.5 Star Member
- Posts: 113
- Joined: Sun Jun 03, 2018 2:22 pm
Snoopy & The Great Pumpkin
Would someone mind taking a look at this drawing and see if you see any obvious mistakes before I attempt to cut please? This is my first trace and I'm not really sure how some of these cuts will play out. For example, the lines on the leaves on each side of the pumpkin... will the torch just make a pass and cut the line the width of the kerf or will it ignore a line that is just standing alone like that?
I do think that I need to go back and adjust those cuts inside of the pumpkin. The ones that run vertical on each side. They seem to measure almost a 1/2 inch wide and I think they should be about 1/4 inch wide.
Anyway, this was my first trace and I'm not very confident in it so I hate to waste a 2 foot piece of metal if there are obvious mistakes.
Thank you in advance for any feedback or advice.
I do think that I need to go back and adjust those cuts inside of the pumpkin. The ones that run vertical on each side. They seem to measure almost a 1/2 inch wide and I think they should be about 1/4 inch wide.
Anyway, this was my first trace and I'm not very confident in it so I hate to waste a 2 foot piece of metal if there are obvious mistakes.
Thank you in advance for any feedback or advice.
You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here
LDR 4'x4' Water Table
Command CNC Linux Controller
Plate Marker
Power Max 45xp w/ Machine Torch & Hand Torch
2 Stage filter, Motorguard filter & HF Ref Dryer
InkScape / SheetCam
Command CNC Linux Controller
Plate Marker
Power Max 45xp w/ Machine Torch & Hand Torch
2 Stage filter, Motorguard filter & HF Ref Dryer
InkScape / SheetCam
- rdj357
- 4 Star Elite Contributing Member
- Posts: 1180
- Joined: Sun Mar 11, 2012 4:40 pm
- Location: Tahlequah, OK
- Contact:
Re: Check dxf please...
Looks good to me - not sure how your software will handle it but there were a few paths that didn't quite make it to join up and a couple places where there were some extra nodes but overall it would probably cut just fine.
Here it is after I did the little minor cleanup in case you want to compare.
Here it is after I did the little minor cleanup in case you want to compare.
You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here
Robert Johnson
----- PlasmaCam 5x10 Table -----
FourNinety Creations & Learn PC, LLC
(918) 457-0289 * Robert@490Creations.com
Plasmacam Goodies! Snap'NCut Mount, AXXON Cards/Cables, Maintenance Items
Learn Plasmacam Workshops
Learn Plasmacam on Facebook
Learn Plasmacam on YouTube
Did I help and you want to help me out? Buy me a coffee! - Thanks!
----- PlasmaCam 5x10 Table -----
FourNinety Creations & Learn PC, LLC
(918) 457-0289 * Robert@490Creations.com
Plasmacam Goodies! Snap'NCut Mount, AXXON Cards/Cables, Maintenance Items
Learn Plasmacam Workshops
Learn Plasmacam on Facebook
Learn Plasmacam on YouTube
Did I help and you want to help me out? Buy me a coffee! - Thanks!
-
- 4 Star Elite Contributing Member
- Posts: 1001
- Joined: Thu Nov 21, 2013 5:32 pm
Re: Snoopy & The Great Pumpkin
thanks for the share..looks great
-
- 2 Star Member
- Posts: 71
- Joined: Mon Oct 02, 2017 3:39 pm
Re: Snoopy & The Great Pumpkin
looks good I will try it
-
- 2 Star Member
- Posts: 77
- Joined: Mon Jan 02, 2017 7:09 am
Re: Snoopy & The Great Pumpkin
Thanks.
- david jordan
- 3.5 Star Member
- Posts: 671
- Joined: Sun Jul 06, 2014 2:21 pm
Re: Snoopy & The Great Pumpkin
Thank you.
PlasmaCam DHC 2 4 X 4 table
Powermax 65
400amp mig welder with dc tig
CRP Bench Top Pro
CS 6,Aspire,Mach 3
Bridgeport
Wells Index mill
10K X 42" Southbend, 6K collets
16" Sothbend, 5C collets
16" Hendy lathe
Everlast Tig200 Amp
PL1220
Powermax 65
400amp mig welder with dc tig
CRP Bench Top Pro
CS 6,Aspire,Mach 3
Bridgeport
Wells Index mill
10K X 42" Southbend, 6K collets
16" Sothbend, 5C collets
16" Hendy lathe
Everlast Tig200 Amp
PL1220
-
- 1.5 Star Member
- Posts: 31
- Joined: Tue Jan 03, 2017 7:05 am
Re: Snoopy & The Great Pumpkin
Thank you everybody loved it....
Chip
Chip
-
- 3 Star Elite Contributing Member
- Posts: 319
- Joined: Thu Mar 31, 2016 2:51 pm
Re: Snoopy & The Great Pumpkin
Love it thanks for sharing
-
- 3 Star Member
- Posts: 360
- Joined: Fri Apr 15, 2011 3:47 am
Re: Snoopy & The Great Pumpkin
This is great, going to cut one for Halloween. Thanks for the share!
- gslavik
- 1.5 Star Member
- Posts: 27
- Joined: Wed Dec 16, 2020 12:18 pm
- Location: Yukon, Okla U.S.A
- Contact:
Re: Snoopy & The Great Pumpkin
Nice work, Thank you for sharing!
-
- 1.5 Star Member
- Posts: 47
- Joined: Fri Aug 16, 2019 9:32 am