Simple question, does anyone own one?, and if so how well does the downdraft design work on it? Pretty simple design with 1 12" hole in the center of the table. Please list your table size and any relevant information.
Thanks in advance!
EZCUT Down Draft Tables?
-
- 2.5 Star Member
- Posts: 123
- Joined: Fri Jan 20, 2017 3:25 am
EZCUT Down Draft Tables?
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
-
- 2.5 Star Member
- Posts: 123
- Joined: Fri Jan 20, 2017 3:25 am
Re: EZCUT Down Draft Tables?
Not a single owner out there than can comment?
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
- see&see
- 2.5 Star Elite Contributing Member
- Posts: 218
- Joined: Tue Jun 24, 2014 12:04 pm
- Location: Minden, Nevada
- Contact:
Re: EZCUT Down Draft Tables?
12" hole?
I use a 20" hole in the side panel with 4' flex duct directly out the wall into a 3000 CFM fan and it's just enough to keep smoke out of the shop on a 4 x 4 table.
I use a 20" hole in the side panel with 4' flex duct directly out the wall into a 3000 CFM fan and it's just enough to keep smoke out of the shop on a 4 x 4 table.
You marry into the PlasmaCam family and must accept the fact your software and hardware are proprietary. It's a for better or for worse engagement with overwhelming security. PlasmaCam controls the computer, table, hardware to their advantage IMO.
-
- 4 Star Elite Contributing Member
- Posts: 1977
- Joined: Fri Apr 17, 2009 11:48 am
Re: EZCUT Down Draft Tables?
I don't have an ezcut downdraft but i do use one of the 12" fans sold here on plasmaspider http://plasmaspider.com/shop/vent_combo.html and it works great in my downdraft setup. No smoke! Works awesome.
-
- 2.5 Star Member
- Posts: 123
- Joined: Fri Jan 20, 2017 3:25 am
Re: EZCUT Down Draft Tables?
Weldguy, how large is your table?
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
-
- 1/2 Star Member
- Posts: 3
- Joined: Thu Nov 09, 2017 5:36 pm
Re: EZCUT Down Draft Tables?
I have a 5x10 down draft. 5000cfm fan, two opens cantered and 1/3 in from each end. Zero smoke.
-
- 2.5 Star Member
- Posts: 123
- Joined: Fri Jan 20, 2017 3:25 am
Re: EZCUT Down Draft Tables?
Just scored a 24" tubeaxial fan, I think that should do it!
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
-
- 2.5 Star Member
- Posts: 123
- Joined: Fri Jan 20, 2017 3:25 am
Re: EZCUT Down Draft Tables?
Do you have any pics of your table setupChris Slade wrote:I have a 5x10 down draft. 5000cfm fan, two opens cantered and 1/3 in from each end. Zero smoke.
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD