I've noticed that I seem to be going through less consumables than I used to. It used to be, whenever there was a problem, and it wasn't cutting all the way through, I'd replace the electrode and nozzle, even after I may have replaced one or the other not too much earlier. I'd be cutting and didn't like the quality, so I'd replace either or from time to time. I felt like I was going through more consumables than I should have been.
Now, when I have an issue, I make sure to zero out the height of the machine (it seems I wasn't doing this and when changing material thickness, the ohmic sensor wouldn't properly work if I didn't "zero Y axis on next cut").
The other thing I do, is replace consumables as a set only. When say going from 45a nozzles to 65a nozzles, I pull the nozzle and electrode out at the same time and put them in the 45a nozzle bin and put the 65a nozzle and electrode in. When after verifying the machine settings and air supply, then and only then do I replace the nozzle/electrode as a set.
So when I want to go from 65a to fine tip, I'll keep the 65a nozzle/electrode set together until the electrode is pretty much trash. At that point I'll get out a new set.
It may not be the best way, but it's what I do now, and I seem to be using less consumables though I'm cutting more... that and not doing bonehead things like putting a 10 gauge sheet on thinking it's 11 ga. or something. I now also have a little sheet metal gauge checker I keep by the cutter at all times. With all this, i seem to have a lot less scrap/consumable use. Anyone who has been cutting much probably already knows this, but for someone starting out, this is what I have learned to help save money.
Cutting back on consumable use
Information on plasma cutting nozzles, electrodes, and other consumables.
Post Reply
1 post
• Page 1 of 1
Post Reply
1 post
• Page 1 of 1
Return to “Plasma Consumables”
Jump to
- WELCOME CENTER, GOOD INFO & MEET OUR SPONSORS
- ↳ Introduce Yourself
- ↳ CNC Plasma Beginners Knowledge Base
- ↳ Contributing Membership Registration or Renewal
- ↳ Our Sponsors & Advertisers
- DXF DESIGN & PROJECT PICTURE SHARING FORUMS
- ↳ DXF & SVG Plasma Cutting File Sharing Forum
- ↳ CNC Plasma Cutter Project Picture Gallery
- ↳ File Conversion Help Wanted
- GENERAL FORUMS
- ↳ CNC Plasma Cutters General Forum
- ↳ Plasma Cut Quality Forum
- ↳ Hypertherm's Basic Tips to Improve Cut Quality
- ↳ Hypertherm's 10 Common Plasma Cutting Mistakes
- ↳ Hypertherm's Tips to Troubleshoot Cut Angularity
- ↳ Pricing, Advertising, & Marketing Your Products Forum
- ↳ Tech Tips From Other Members
- ↳ Classified Ads
- PLASMA CUTTER FORUMS
- ↳ Hypertherm Plasma Cutters
- ↳ Powermax Helpful Resources
- ↳ Powermax Cut Speed Charts
- ↳ Powermax Cut Speed Charts
- ↳ Powermax SYNC 65, 85, 105 Cut Speed Charts
- ↳ Powermax 45 Cut Speed Charts
- ↳ Powermax 65/85 Cut Speed Charts
- ↳ Powermax 105 Cut Speed Charts
- ↳ Powermax 125 Cut Speed Charts
- ↳ Powermax Fault Code, Diagnostics, & Troubleshooting Forums
- ↳ Powermax 65 & 85 Common Fault Code, Diagnotics, & Troubleshooting Forum
- ↳ 0-12 Fault Code
- ↳ 0-19 Fault Code
- ↳ 0-20 Fault Code
- ↳ 0-21 Fault Code
- ↳ 0-22 Fault Code
- ↳ 0-30 Fault Code
- ↳ 0-99 fault Code
- ↳ Displaying the Powermax 65 85 Service Screen
- ↳ Thermal Dynamics / Esab Plasma Cutters
- ↳ Cutmaster A40 Cut Speed Charts
- ↳ Cutmaster A60 Cut Speed Charts
- ↳ Cutmaster A80 Cut Speed Charts
- ↳ Cutmaster A120 Cut Speed Charts
- ↳ Lincoln & Miller Plasma Cutters
- ↳ RazorWeld, Everlast, & All Other Plasma Cutters
- ↳ Plasma Consumables
- CNC PLASMA TABLE & CONTROLLER FORUMS
- ↳ CandCNC Forum
- ↳ CandCNC Website
- ↳ FastCut CNC Forum
- ↳ FlashCut CNC Forum
- ↳ JD Squared Forum
- ↳ JD Squared Website
- ↳ Shop Sabre Forum
- ↳ Star-Lab CNC Forum
- ↳ Tracker CNC Forum
- ↳ Langmuir Crossfire Forum
- ↳ PlasmaCam, Samson, & Go Torch Forum
- ↳ Torchmate Forum
- ↳ DIY Plasma Table & Accessory Discussion Forum
- ↳ Various Manufacturers Forum
- CAD-CAM & CONTROL SOFTWARE FORUMS
- ↳ General Discussion
- ↳ Fusion 360 & AutoCAD Forum
- ↳ Get AutoDesk Fusion 360 FREE
- ↳ BobCAD
- ↳ C&CNC CommandCNC
- ↳ Corel Draw Graphics Suite
- ↳ CorelDRAW Free 30 day trial
- ↳ Quick & Helpful CorelDRAW Tutorial Videos
- ↳ Inkscape
- ↳ Download Inkscape for Windows
- ↳ Linux CNC - Plasmac
- ↳ Mach3 & Mach4 CNC
- ↳ Plasmacam - DesignEdge
- ↳ SheetCam
- ↳ Torchmate Software
- METAL FINISHING FORUMS
- ↳ Patina Finishes
- ↳ Steel F/X Your Metal Patina & Dye Connection
- ↳ Paint & Other Top Coats
- ↳ Powder Coat
- ↳ Abrasive & Texturing
- ↳ Dross/Slag Removal
- ACCESSORIES & RELATED TOOL FORUMS
- ↳ EasyScriber Drag Style Scriber for Hypertherm
- ↳ EasyScriber for Hypertherm, Thermal Dynamics, Razorweld, Esab
- ↳ Plate Markers, & Air Scribes
- ↳ Mig Welders, Tig Welders, Spot Welders
- ↳ Metal Bending, Rolling, Notching, Drilling, Saw Cutting
- ↳ Air Dryers, Air Filters, Air Compressors, Etc.
- ↳ Water Tables, Ventilation, Air Handling
- ↳ Fab Tables, Grind Stations, Material Storage & Handling
- ↳ Pen Markers, Remote Controls, Drawing Tablets, etc.
- ↳ 3D Printers & Printed Accessories
- ↳ Laser Engravers & Cutters
- ↳ Arclight Dynamics