Expanding my setup

wickedinhere · Post by **wickedinhere** » Fri Jun 01, 2012 1:07 pm

Here are the oven build pics.

wickedinhere · Post by **wickedinhere** » Fri Jun 01, 2012 1:08 pm

wickedinhere · Post by **wickedinhere** » Fri Jun 01, 2012 1:10 pm

wickedinhere · Post by **wickedinhere** » Fri Jun 01, 2012 1:11 pm

wickedinhere · Post by **wickedinhere** » Fri Jun 01, 2012 1:12 pm

sodfarmer · Post by **sodfarmer** » Fri Jun 01, 2012 2:51 pm

Would you mind sharing where you purchased your fan and the PN#? Thanks

wickedinhere · Post by **wickedinhere** » Fri Jun 01, 2012 3:00 pm

I got it at graingers and its a Dayton 1TDU9 High Temperature Blower, 115 Volt, 76 CFM some people use higher cfm fans but this one is perfect.

frodin1 · Post by **frodin1** » Fri Jun 01, 2012 5:02 pm

What did you end up using inside the walls as insulation? Is that just OSB or expanding foam, kind of hard to tell from pics?

wickedinhere · Post by **wickedinhere** » Fri Jun 01, 2012 5:35 pm

Mineral wool

alleykat · Post by **alleykat** » Sat Jun 02, 2012 4:19 am

I would like to make a bigger oven than I already have but I dont know if I should mess with wiring.

Post by **Copp3r** » Sat Sep 15, 2012 1:29 am

Great looking oven... To each his own, and certainly I am biased but I prefer my roll in / flat bottom to the idea of having the oven on wheels. There are pro's and con's to each. I don't see the need to move the oven... ... and I have a rack that I hang my projects from, apply the powder coat and then wheel the rack right in to the oven. When the baking portion is over and done with, I merely roll out the rack.

Thanks for the images on the application booth. You must have been reading my mind. I've got a new shop underway and one of the items I want to built is a place to apply the powder coats. Without a booth the powder goes everywhere.

Thx

Copp3r / roger

wickedinhere · Post by **wickedinhere** » Sun Sep 23, 2012 3:53 pm

Thanks, a rack system would be nice.

SeanP · Post by **SeanP** » Mon Jan 12, 2015 10:29 am

Nice Job!
Can I just ask what the total wattage of the elements are?
Do you find them about right for that size of oven?
Thanks
Sean

wickedinhere · Post by **wickedinhere** » Mon Jan 12, 2015 5:49 pm

12000 total watts it works great great recovery time when opening the door.

SeanP · Post by **SeanP** » Mon Jan 12, 2015 5:51 pm

Good stuff, thanks

radnurse68 · Post by **radnurse68** » Sun Feb 01, 2015 11:43 pm

Do you mind sharing your cost on your oven build? There is an used oven nearby for sale that is the same deminsions as yours. It is several years old and has been setting outside in the weather for a year or so. The current owner has never fired it up but says he will guaranty that it works for $1500 and will sell at $1000 without the guaranty.

wickedinhere · Post by **wickedinhere** » Wed Feb 18, 2015 9:11 am

I have around 16-1800 in it.

CNCCAJUN · Post by **CNCCAJUN** » Thu Feb 19, 2015 10:39 am

wickedinhere wrote:Thanks, it hits 400 in 17 minutes I will post pics of my booth when i start.

Have you calculated a cost per hour for your oven yet . . .?

Steve

wickedinhere · Post by **wickedinhere** » Thu Feb 19, 2015 1:22 pm

I have not but it doesn't it doesn't cost that much to run. I don't run it all day but when i do run it its for a few hours at a time. I try to get 5 or 6 pieces lined up to powder coat at one time so i am not just doing one item at a time.

Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup

Re: Expanding my setup