It is currently Mon Dec 11, 2017 2:18 am

 

I Need Help. Options for fire pits

Learn and share patina finishing techniques, experiences, and product knowledge here.
plasmartist
Posts: 39
Joined: Mon Aug 07, 2017 1:31 pm

I Need Help. Options for fire pits

Postby plasmartist » Thu Aug 24, 2017 2:40 pm

To start off, I have sold about 30 fire pits so far and every customer has been a fan of developing a natural patina, except one; and he wants to buy quite a few as gifts for his clients so I am trying to learn what options I have. My fire pits are a flat pack design for portability, so it is important that I find something that wont leave ugly scratches when the parts are folded down and bumping around in the back of a car or pickup. I told the customer to wipe or spray some vegetable oil on the parts after fires, much like cast iron pans, but he seems to be less than satisfied with this option. Part of me wants to just kick this customer to the curb, but I also want to overcome this challenge because the rust look wont always be popular and learning something new never hurts.

I am personally a fan of the rust look, so to date I have not experimented with high heat rust prevention. I have purchased some 2000 degree clear coat and I will be experimenting with its results along with another pit that will just spray Pam on.

Thanks

User avatar
little blue choo
Elite Contributing Member
Elite Contributing Member
Posts: 1311
Joined: Mon Mar 02, 2015 10:38 pm
Location: Cherryville NC
Contact:

Re: I Need Help. Options for fire pits

Postby little blue choo » Thu Aug 24, 2017 9:09 pm

No paint will hold up. It doesn't matter what temperature it is rated for. You are building a knock down type pit and it will scratch the first time you use it. I use flat black so the customer can touch it up easily.

Rick
Rick
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape

User avatar
tnbndr
Elite Contributing Member
Elite Contributing Member
Posts: 1361
Joined: Mon Jan 09, 2012 4:30 pm
Location: New Berlin, WI
Contact:

Re: I Need Help. Options for fire pits

Postby tnbndr » Fri Aug 25, 2017 9:20 am

I would say you are fighting a losing battle, especially with a knock down which there is no way to guarantee it won't scratch the finish. This is just common sense, if the customer doesn't get it, oh well. If he wants assembled and welded pits with a finish you could try some of the high heat engine paints or barbecue paints.
I just tell customers that I don't use them and if they intend on painting the fire pit I just make sure they have clean metal when they pick it up. I have had no takers on that option yet.
Dennis
LDR 4x8, Scribe, DTHCIV
PM45
DeVilbiss Air America 6.5HP, 80Gal., 175psi, Two Stage
[email protected], [email protected]
Miller 211
RW 390E Slip Roll
AutoCAD, SheetCAM, Mach 3
https://www.facebook.com/ikescreations?ref=hl
http://ikescreations.com

plasmartist
Posts: 39
Joined: Mon Aug 07, 2017 1:31 pm

Re: I Need Help. Options for fire pits

Postby plasmartist » Sun Aug 27, 2017 2:09 pm

Thanks for your replies. I have been on the same boat, but was hoping I was ignorant to some miracle product. I think that for those that dont want the rust look, I will offer stainless as an option.

Bigdogbro1
Posts: 100
Joined: Tue Aug 18, 2015 9:20 am

Re: I Need Help. Options for fire pits

Postby Bigdogbro1 » Tue Sep 26, 2017 2:10 pm

Maybe HOT dipped galvanized if the silver color isn't any problem.

User avatar
Scratch
Elite Contributing Member
Elite Contributing Member
Posts: 418
Joined: Tue Sep 01, 2009 9:07 pm
Location: Hudson,WI
Contact:

Re: I Need Help. Options for fire pits

Postby Scratch » Tue Sep 26, 2017 6:53 pm

Bigdogbro1 wrote:Maybe HOT dipped galvanized if the silver color isn't any problem.

I don't think burning galvanized steel around a bunch of people roasting marshmallows is a good idea...?

Yeah, no coating is gonna hold up. The customer is going to have to deal with it.
I think I'm the oldest 10 year old boy on the forum...


Return to “Patina Finishes”

Who is online

Users browsing this forum: No registered users and 2 guests