Collapsible fire pit

bwv1993 · Post by **bwv1993** » Mon Sep 24, 2018 7:00 pm

Would someone have a design they would like to share for a collapsible fire pit like the one in the picture? Doesn't need the stars. I'll put my own design in.

Thanks!

dhannahjr45 · Post by **dhannahjr45** » Mon Sep 24, 2018 7:37 pm

this might be what you are hunting for

SUPPORT.DXF

SIDE PLATE.DXF

SIDE PLATE moose.dxf

SIDE PLATE bear.dxf

BOTTOM PLATE.DXF

bwv1993 · Post by **bwv1993** » Tue Sep 25, 2018 6:17 pm

Awesome! Thank you very much!=

stjohnwelding · Post by **stjohnwelding** » Tue Sep 25, 2018 7:48 pm

thank you . it came out awesome. great job.

Jhonea78 · Post by **Jhonea78** » Wed Sep 26, 2018 1:39 am

anyway someone could convert this to an svg file for use in Inkscape?

Post by **ironhorse** » Wed Sep 26, 2018 5:35 am

Really cool, thank you.

Billythegoat · Post by **Billythegoat** » Wed Sep 26, 2018 7:03 am

Jhonea, try using convertio. Most of the time it it does a pretty good job but be sure to look for rogue lines and such.

Post by **ggeh** » Wed Sep 26, 2018 9:38 am

Very nice design, Thanks for sharing

dikko · Post by **dikko** » Thu Sep 27, 2018 8:31 pm

thx for the share

Post by **Ronz2Busy** » Fri Sep 28, 2018 2:20 pm

Really nice! Thank You for sharing.

JohnnyC · Post by **JohnnyC** » Sat Sep 29, 2018 9:16 am

Nice Thanks for the share!

Post by **K D Metalwerks** » Mon Oct 15, 2018 8:13 pm

Any ideas on steel thickness? I am thinking 1/4" judging from slots size for support plate.

YouTube · Post by **Fastyankee** » Tue Oct 16, 2018 8:11 am

Thanks for the share.

MetalheadLLC · Post by **MetalheadLLC** » Fri Nov 02, 2018 11:04 am

K D Metalwerks wrote:Any ideas on steel thickness? I am thinking 1/4" judging from slots size for support plate.

My thoughts exactly! Slots are .45 and .5, so 1/4" would slide in and then slant as the picture shows.

Post by **flyingwelder** » Sun Jan 06, 2019 10:47 am

LOOKS GREAT THANKS

SNLLC · Post by **SNLLC** » Thu May 09, 2019 1:51 pm

Note that there is a different in the file the OP posted and the file provided. The assembly is different based on the way the top corner tabs are cut into the siders. The Picture in the original post had sides that were, essentially, either male or female so you needed 2 of each and they would slide into the corresponding slots on the opposite piece. The files attached above have a male and a female side on each panel so that when assembled you have to be able to left the last corner to get e everything to fit together. Just like folding down a 4 sided box top. Having dedicated male or female panels makes assembly and disassembly easier since you don't have to slightly remove the first panel to engage with the 4th.

t300 · Post by **t300** » Fri Dec 11, 2020 1:38 pm

has anyone cut the dxf that were posted here? Wondering how it worked before I blow a sheet on it. Looking to make one a bit bigger (this one size on top is 32" and only 10" tall. Want to make one closer to 4 feet and 14" tall or so, not sure if its worth to modify this or start from scratch

Collapsible fire pit

Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit

Re: Collapsible fire pit