Can Yall help me convert this

For general topics and questions that do not fit into any of the other categories or forums.
Post Reply
User avatar
Sampson Jones
3 Star Elite Contributing Member
3 Star Elite Contributing Member
Posts: 333
Joined: Mon Jul 25, 2011 9:30 pm

Can Yall help me convert this

Post by Sampson Jones »

I did this in Gimp , then converted it in Inkscape to svg. and dxf. but nothing shows up when I import it to sheetcam ? Im new at this so anyhelp would be greatly appreciated . What should I do in the future ?
Thanks !

You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here

My design , 4ft x 8 ft water table
CandCNC electronics
Hypertherm powermax 65
Command Lineux
Super z 2
Sheetcam
Inkscape and corel draw
User avatar
Metal Lee
2.5 Star Elite Contributing Member
2.5 Star Elite Contributing Member
Posts: 190
Joined: Sun Oct 05, 2008 3:10 pm

Re: Can Yall help me convert this

Post by Metal Lee »

Tried to open and import to X5 and no can see, post the .svg file. And I will see what I can do.
Thanks, Metal Lee
Keep the sparks out of your boots!
User avatar
Sampson Jones
3 Star Elite Contributing Member
3 Star Elite Contributing Member
Posts: 333
Joined: Mon Jul 25, 2011 9:30 pm

Re: Can Yall help me convert this

Post by Sampson Jones »

Hey , this site says "svg upload not allowed " ? Heres a png file, I also have jpeg if that will help . Thanks !!!!!

You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here

Last edited by Sampson Jones on Thu Sep 01, 2011 12:57 pm, edited 1 time in total.
My design , 4ft x 8 ft water table
CandCNC electronics
Hypertherm powermax 65
Command Lineux
Super z 2
Sheetcam
Inkscape and corel draw
User avatar
Sampson Jones
3 Star Elite Contributing Member
3 Star Elite Contributing Member
Posts: 333
Joined: Mon Jul 25, 2011 9:30 pm

Re: Can Yall help me convert this

Post by Sampson Jones »

Thanks , I really love this site !
My design , 4ft x 8 ft water table
CandCNC electronics
Hypertherm powermax 65
Command Lineux
Super z 2
Sheetcam
Inkscape and corel draw
User avatar
Streetwerkz
2.5 Star Elite Contributing Member
2.5 Star Elite Contributing Member
Posts: 152
Joined: Sun Aug 30, 2009 7:33 pm
Location: Columbus,Oh
Contact:

Re: Can Yall help me convert this

Post by Streetwerkz »

still needs werk, but heres a good start for ya

You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here

Joshua Robinson
www.Streetwerkz.com
User avatar
Sampson Jones
3 Star Elite Contributing Member
3 Star Elite Contributing Member
Posts: 333
Joined: Mon Jul 25, 2011 9:30 pm

Re: Can Yall help me convert this

Post by Sampson Jones »

Hey Steelwerks , thanks ! More questions though , what more work on this would you suggest ? How would you set up this operation in S.C. ? Holding tabbs , offsets , cut paths etc ? Someday, after I learn this stuff , I will use this as my sign , to help offset the cost of my new table I built .
Thanks !!
My design , 4ft x 8 ft water table
CandCNC electronics
Hypertherm powermax 65
Command Lineux
Super z 2
Sheetcam
Inkscape and corel draw
User avatar
Metal Lee
2.5 Star Elite Contributing Member
2.5 Star Elite Contributing Member
Posts: 190
Joined: Sun Oct 05, 2008 3:10 pm

Re: Can Yall help me convert this

Post by Metal Lee »

Oh ya I new that once, looks like SW hooked you up.



Sampson Jones wrote:Hey , this site says "svg upload not allowed " ? Heres a png file, I also have jpeg if that will help . Thanks !!!!!
User avatar
Streetwerkz
2.5 Star Elite Contributing Member
2.5 Star Elite Contributing Member
Posts: 152
Joined: Sun Aug 30, 2009 7:33 pm
Location: Columbus,Oh
Contact:

Re: Can Yall help me convert this

Post by Streetwerkz »

I use BobCad to drawl in & cut from it, not familiar with sheet cam.
the picture still needs the drop outs fixed so the entire torch doesn't just fall through the sign.
thats something you will have to determine how you want to do (what you want to be a positive or negative space in the sign)

good luck, it will be a cool sign when its done, post up some pics!!!
Joshua Robinson
www.Streetwerkz.com
Post Reply

Return to “CNC Plasma Cutters General Forum”