EZCUT Down Draft Tables?

For general topics and questions that do not fit into any of the other categories or forums.
Post Reply
tylerd
2.5 Star Member
2.5 Star Member
Posts: 123
Joined: Fri Jan 20, 2017 3:25 am

EZCUT Down Draft Tables?

Post by tylerd »

Simple question, does anyone own one?, and if so how well does the downdraft design work on it? Pretty simple design with 1 12" hole in the center of the table. Please list your table size and any relevant information.

Thanks in advance!
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
tylerd
2.5 Star Member
2.5 Star Member
Posts: 123
Joined: Fri Jan 20, 2017 3:25 am

Re: EZCUT Down Draft Tables?

Post by tylerd »

Not a single owner out there than can comment?
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
User avatar
see&see
2.5 Star Elite Contributing Member
2.5 Star Elite Contributing Member
Posts: 218
Joined: Tue Jun 24, 2014 12:04 pm
Location: Minden, Nevada
Contact:

Re: EZCUT Down Draft Tables?

Post by see&see »

12" hole?

I use a 20" hole in the side panel with 4' flex duct directly out the wall into a 3000 CFM fan and it's just enough to keep smoke out of the shop on a 4 x 4 table.
You marry into the PlasmaCam family and must accept the fact your software and hardware are proprietary. It's a for better or for worse engagement with overwhelming security. PlasmaCam controls the computer, table, hardware to their advantage IMO. :x
weldguy
4 Star Elite Contributing Member
4 Star Elite Contributing Member
Posts: 1928
Joined: Fri Apr 17, 2009 11:48 am

Re: EZCUT Down Draft Tables?

Post by weldguy »

I don't have an ezcut downdraft but i do use one of the 12" fans sold here on plasmaspider http://plasmaspider.com/shop/vent_combo.html and it works great in my downdraft setup. No smoke! Works awesome.
tylerd
2.5 Star Member
2.5 Star Member
Posts: 123
Joined: Fri Jan 20, 2017 3:25 am

Re: EZCUT Down Draft Tables?

Post by tylerd »

Weldguy, how large is your table?
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
Chris Slade
1/2 Star Member
1/2 Star Member
Posts: 3
Joined: Thu Nov 09, 2017 5:36 pm

Re: EZCUT Down Draft Tables?

Post by Chris Slade »

I have a 5x10 down draft. 5000cfm fan, two opens cantered and 1/3 in from each end. Zero smoke.
tylerd
2.5 Star Member
2.5 Star Member
Posts: 123
Joined: Fri Jan 20, 2017 3:25 am

Re: EZCUT Down Draft Tables?

Post by tylerd »

Just scored a 24" tubeaxial fan, I think that should do it!
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
tylerd
2.5 Star Member
2.5 Star Member
Posts: 123
Joined: Fri Jan 20, 2017 3:25 am

Re: EZCUT Down Draft Tables?

Post by tylerd »

Chris Slade wrote:I have a 5x10 down draft. 5000cfm fan, two opens cantered and 1/3 in from each end. Zero smoke.
Do you have any pics of your table setup
Bulltear 4x8
PN200 Pendant
Linux Command CNC
Hypertherm PM 85
C&CNC Bladerunner Servo
DTHC IV Feather Touch
HyT-Connect DCP-01
Sheetcam Inkscape QCAD
Post Reply

Return to “CNC Plasma Cutters General Forum”