Tattered and Torn Flag "Wind Wave"
-
- 1.5 Star Member
- Posts: 30
- Joined: Tue Jun 27, 2017 2:48 am
Tattered and Torn Flag "Wind Wave"
I've only cut them in the flat however I have seen some that have a wave in them and was wondering what method people were using to gain that. Thanks in advance!!!
2017 Shop Sabre SideKick 4
Upgrades: Marker/Plotter, Laser sights, Engraver
Hypertherm PM65
Upgrades: Marker/Plotter, Laser sights, Engraver
Hypertherm PM65
- acourtjester
- 6 Star Elite Contributing Member
- Posts: 7796
- Joined: Sat Jun 02, 2012 6:04 pm
- Location: Pensacola, Fla
Re: Tattered and Torn Flag "Wind Wave"
If I remember correctly they cut the flag and then used a plate roller to put waves into the flag.
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
- rdj357
- 4 Star Elite Contributing Member
- Posts: 1171
- Joined: Sun Mar 11, 2012 4:40 pm
- Location: Tahlequah, OK
- Contact:
Re: Tattered and Torn Flag "Wind Wave"
*blush* I use my knee on 16 gauge. LOL
Robert Johnson
----- PlasmaCam 5x10 Table -----
FourNinety Creations & Learn PC, LLC
Plasmacam Goodies! Snap'NCut Mount, AXXON Cards/Cables, Maintenance Items
Learn Plasmacam Workshops
Learn Plasmacam on Facebook
Learn Plasmacam on YouTube
----- PlasmaCam 5x10 Table -----
FourNinety Creations & Learn PC, LLC
Plasmacam Goodies! Snap'NCut Mount, AXXON Cards/Cables, Maintenance Items
Learn Plasmacam Workshops
Learn Plasmacam on Facebook
Learn Plasmacam on YouTube
- little blue choo
- 4 Star Member
- Posts: 1460
- Joined: Mon Mar 02, 2015 10:38 pm
- Location: Cherryville NC
- Contact:
Re: Tattered and Torn Flag "Wind Wave"
I made a jig for my press. It is two pieces, I used pipe on the bottom spaced out to where the pipe on the top piece will press between them. Works like a champ.
Rick
Rick
Rick
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
-
- 2.5 Star Member
- Posts: 164
- Joined: Sat Nov 30, 2013 7:01 pm
- Location: Buffalo Gap, TX
Re: Tattered and Torn Flag "Wind Wave"
I just clamp a piece of tubing to the edge of the table and hand form the waves over the top of that.
Derek
Precision Plasma LD 4x8
CandCNC BladeRunner EtherCut Mark IV
HT PM 45
Precision Plasma LD 4x8
CandCNC BladeRunner EtherCut Mark IV
HT PM 45