New here, thought I'd say hello...
-
- 1 Star Member
- Posts: 13
- Joined: Fri Mar 03, 2017 4:33 pm
New here, thought I'd say hello...
So I've decide to purchase a plasma table. I'm currently leaning towards an arclight 5x10. I am also considering a JD2 as well as a bulltear. Anyhow, I'm a software engineer by trade. I'm really hoping to grow this into something to help offset my other hobbies. Sandrails, jeeps, rzr etc. Until I can get some side business cutting stuff for others I will be selling stuff through my in-laws store. Fire pits, wall art etc. I'm also looking for other ideas that I can sell locally.
- little blue choo
- 4 Star Member
- Posts: 1460
- Joined: Mon Mar 02, 2015 10:38 pm
- Location: Cherryville NC
- Contact:
Re: New here, thought I'd say hello...
Welcome.
Rick
Rick
Rick
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
-
- 3.5 Star Member
- Posts: 681
- Joined: Wed Nov 26, 2014 5:12 pm
Re: New here, thought I'd say hello...
Welcome to the site
- Nacs Fab
- 3 Star Member
- Posts: 328
- Joined: Tue Dec 04, 2012 4:11 pm
- Location: Columbia, MO
Re: New here, thought I'd say hello...
Welcome and good Luck on your Purchase.
I would recommend Bulltear tables. I don't personally own one, but after building mine, I really like their design. You cannot beat the linear rails and nice Z drive and of course the best feature is no rails in the way when sheet loading. BIG Plus! My next table will be a Bulltear.
LDR would be my second choice as they have excellent support so I have seen and their design is very nice as well.
Of course for electronics, Candcnc products are top notch and Tom is here on the forums answering questions and such. Excellent Support as well!
Lastly, do not even think about any other company than Hypertherm for your Plasma Unit. We also have Jim Colt here on the forum and not only is he a Hypertherm Representative, he owns and operates several CNC Machines in his home shop.
I would recommend Bulltear tables. I don't personally own one, but after building mine, I really like their design. You cannot beat the linear rails and nice Z drive and of course the best feature is no rails in the way when sheet loading. BIG Plus! My next table will be a Bulltear.
LDR would be my second choice as they have excellent support so I have seen and their design is very nice as well.
Of course for electronics, Candcnc products are top notch and Tom is here on the forums answering questions and such. Excellent Support as well!
Lastly, do not even think about any other company than Hypertherm for your Plasma Unit. We also have Jim Colt here on the forum and not only is he a Hypertherm Representative, he owns and operates several CNC Machines in his home shop.
Shop Droids Plasmabot 3.0 DIY 4x8 with water table
G540 with LCTHC by candcnc
Hypertherm 1250 with Duramax Torch Upgrade
all built... by me...
G540 with LCTHC by candcnc
Hypertherm 1250 with Duramax Torch Upgrade
all built... by me...