Just got my first package with SteelFX dyes and have been trying them out. I'm sold on them! Here are a couple bass, our first test on dyeing metal. Hopefully as time goes on I can figure out how to improve the color blending.
Thanks, SteelFX!
Bass
-
- 2.5 Star Member
- Posts: 199
- Joined: Mon Dec 08, 2014 4:33 pm
- Location: Gentry, AR
- Contact:
Bass
5x10 Dynatorch High Definition plasma table. Cuttingshop drawing program. Sigmanest nesting program. Custom fabrication and powder coating.
Whatsoever thy hand findeth to do, do it with thy might Ecclesiastes 9:10
Whatsoever thy hand findeth to do, do it with thy might Ecclesiastes 9:10
- Larry83301
- 5 Star Elite Contributing Member
- Posts: 2647
- Joined: Tue Oct 27, 2009 6:36 pm
- Location: Twin Falls, Idaho
Re: Bass
Nice looking fish!
Larry
Larry
- WyoGreen
- 4 Star Member
- Posts: 897
- Joined: Tue Mar 04, 2014 8:36 pm
- Location: Cheyenne, Wyoming
Re: Bass
Looks like you have a pretty good handle on the dyes already!
Steve
Steve
Precision Plasma gantry
CommandCNC Linux controller w/Feather Touch & PN200 hand controller
HT-45 plasma cutter
Plate Marker
Router
Laser
CommandCNC Linux controller w/Feather Touch & PN200 hand controller
HT-45 plasma cutter
Plate Marker
Router
Laser
- little blue choo
- 4 Star Member
- Posts: 1460
- Joined: Mon Mar 02, 2015 10:38 pm
- Location: Cherryville NC
- Contact:
Re: Bass
Looks to me like you've got this covered. Enjoy my friend. I will give one secret, if you clear coat apply your first coat lightly and allow to flash over , then apply a heavy coat. If you apply a heavy coat on the first coat the dye tends to run and bleed at times. After learning to apply first coat light and then second coat heavy I haven't had any problems.
Rick
Rick
Rick
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
-
- 2.5 Star Member
- Posts: 199
- Joined: Mon Dec 08, 2014 4:33 pm
- Location: Gentry, AR
- Contact:
Re: Bass
Thanks for the suggestion! I'll take all the help I can get!...little blue choo wrote:Looks to me like you've got this covered. Enjoy my friend. I will give one secret, if you clear coat apply your first coat lightly and allow to flash over , then apply a heavy coat. If you apply a heavy coat on the first coat the dye tends to run and bleed at times. After learning to apply first coat light and then second coat heavy I haven't had any problems.
Rick
5x10 Dynatorch High Definition plasma table. Cuttingshop drawing program. Sigmanest nesting program. Custom fabrication and powder coating.
Whatsoever thy hand findeth to do, do it with thy might Ecclesiastes 9:10
Whatsoever thy hand findeth to do, do it with thy might Ecclesiastes 9:10