I love the way this came out! 16ga, cold rolled. buffed. painted. looks bad a$$
tattered flag
- Capstone
- 4 Star Member
- Posts: 1015
- Joined: Fri Sep 13, 2013 8:42 am
- Location: Washington D.C. Metro
- Contact:
Re: tattered flag
That's pretty sharp. Is that the spray anodizing paint?
Phil
It's all relative...
CNC Metal Design
Instagram CNC Metal Design
JD Squared 4x8
HT PM45, Miller 251 MIG
It's all relative...
CNC Metal Design
Instagram CNC Metal Design
JD Squared 4x8
HT PM45, Miller 251 MIG
-
- 4 Star Member
- Posts: 950
- Joined: Thu Jan 02, 2014 6:33 pm
Re: tattered flag
Looks good. I bet it took a while to paint
Torchmate 2x2 - Flashcut
Powermax 45 - Machine torch
Taig CNC Mill - Flashcut
Razorweld Distributor
Powermax 45 - Machine torch
Taig CNC Mill - Flashcut
Razorweld Distributor
-
- 2.5 Star Member
- Posts: 148
- Joined: Fri Jun 28, 2013 4:36 pm
Re: tattered flag
Thanks guys, by the way a big thanks to the ps community here! It's the spray anodize paint... It was a lot of masking to paint this properly for sure!
-
- 4 Star Member
- Posts: 950
- Joined: Thu Jan 02, 2014 6:33 pm
Re: tattered flag
My anodized spray paint is never the vibrant. Even with a primer. Any special tricks ?
Torchmate 2x2 - Flashcut
Powermax 45 - Machine torch
Taig CNC Mill - Flashcut
Razorweld Distributor
Powermax 45 - Machine torch
Taig CNC Mill - Flashcut
Razorweld Distributor
-
- 1.5 Star Member
- Posts: 25
- Joined: Fri Mar 11, 2016 2:45 pm
- rons
- 2.5 Star Member
- Posts: 179
- Joined: Thu Jul 23, 2015 2:26 pm
- Location: Charlotte, NC
Re: tattered flag
Did mine with an old look using acid and airbrushing
4x8 Home made with PPL Gantry
Bladder water table
Candcnc EtherCut + DTHCIV
Hypertherm PM 65 machine
Sheetcam, Mach 3
Corel DrawX7
TurboCad 2015
211 Miller Mig
Ingersoll Rand 7.5 hp 80 gal
Harbor Ref. Dryer
Lathe, BP, 1" x 12" Cosan Miter Saw,
Bladder water table
Candcnc EtherCut + DTHCIV
Hypertherm PM 65 machine
Sheetcam, Mach 3
Corel DrawX7
TurboCad 2015
211 Miller Mig
Ingersoll Rand 7.5 hp 80 gal
Harbor Ref. Dryer
Lathe, BP, 1" x 12" Cosan Miter Saw,
- acourtjester
- 6 Star Elite Contributing Member
- Posts: 7796
- Joined: Sat Jun 02, 2012 6:04 pm
- Location: Pensacola, Fla
Re: tattered flag
I have mine cut and painted but cannot figure how to make it look distressed, I don't have an air brush and am a little lacking in the artistic department.
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
-
- 4 Star Member
- Posts: 950
- Joined: Thu Jan 02, 2014 6:33 pm
Re: tattered flag
Would a red scotch brite pad work?acourtjester wrote:I have mine cut and painted but cannot figure how to make it look distressed, I don't have an air brush and am a little lacking in the artistic department.
Torchmate 2x2 - Flashcut
Powermax 45 - Machine torch
Taig CNC Mill - Flashcut
Razorweld Distributor
Powermax 45 - Machine torch
Taig CNC Mill - Flashcut
Razorweld Distributor