Search found 9 matches

by LMKkustoms
Wed Oct 14, 2015 12:50 am
Forum: CNC Plasma Cutters General Forum
Topic: gantry rebuild question
Replies: 6
Views: 819

Re: gantry rebuild question

im using 1.5 x 4.5 80/20 for my gantry laid on edge so my torch travels on the 1.5 side if you look at arclights table they are using 1.5 s 4.5 1.5 side up
by LMKkustoms
Thu Oct 08, 2015 1:30 pm
Forum: CNC Plasma Cutter Project Picture Gallery
Topic: A few finished projects
Replies: 4
Views: 1055

Re: A few finished projects

thank you all for the compliments
by LMKkustoms
Tue Oct 06, 2015 9:37 am
Forum: CNC Plasma Cutter Project Picture Gallery
Topic: A few finished projects
Replies: 4
Views: 1055

A few finished projects

just a few of the pieces i have made sense getting my plasma table built
by LMKkustoms
Fri Jul 17, 2015 6:09 am
Forum: CNC Plasma Cutters General Forum
Topic: New build 5x10
Replies: 25
Views: 3247

Re: New build 5x10

acourtjester i was wondering where you got the little wedge for the micro switch to hit im working on a new table build and i like the way you have your switch hitting the wedge and cant seem to find a wedge like that
by LMKkustoms
Fri Mar 14, 2014 3:03 am
Forum: CNC Plasma Cutters General Forum
Topic: need a little advice with home built table
Replies: 11
Views: 1594

Re: need a little advice with home built table

figured it out finally i think. every time i would unhook the ground clamp from my table the voltage dro would drop to 0 and as soon as i would hook it back to the table it would go up to 20 to 30 i have come to the conclusion that i made the table frame from drill stem and its got a magnetic proper...
by LMKkustoms
Sat Mar 08, 2014 10:46 pm
Forum: CNC Plasma Cutters General Forum
Topic: need a little advice with home built table
Replies: 11
Views: 1594

Re: need a little advice with home built table

im still trying to figure out why i have to ground my table to the sub panel to make the dtch dro go to 0volts when its all ready got a ground rod
by LMKkustoms
Fri Mar 07, 2014 1:41 am
Forum: CNC Plasma Cutters General Forum
Topic: need a little advice with home built table
Replies: 11
Views: 1594

Re: need a little advice with home built table

ok so new tips in and im still having problems trying to cut 16ga. My settings are 30amps with 45amp nozzles 200ipm and i started at 111v and worked my way all the way 90v and as soon as i turn the thc on it cuts about 6 inches of the 12inch test line and starts to rise anyone i even tried the setti...
by LMKkustoms
Tue Mar 04, 2014 1:59 am
Forum: CNC Plasma Cutters General Forum
Topic: need a little advice with home built table
Replies: 11
Views: 1594

Re: need a little advice with home built table

im waiting for some new some new nozzles to come in the mail but i was messing around today in garage and with my plasma turned off if i unplug the ground to the 110v from my table i still have 20volts on my thc im still trying to figure whats going on with it.
by LMKkustoms
Sun Mar 02, 2014 3:30 am
Forum: CNC Plasma Cutters General Forum
Topic: need a little advice with home built table
Replies: 11
Views: 1594

need a little advice with home built table

Im having some problems with my home built table. I having problems with my candcnc Dthc2 and im not sure why it does what it does. i cut 16 and 18 ga mostly with the thc off i get a decent cut but if i turn the thc on it will still start cutting fine then the torch just starts rasing up and up till...

Go to advanced search